ups_eaton_9px:
    walk:
      #- upsIdentName # Serial number => xupsIdentSerialNumber
      - xupsBatCapacity # % of charged
      - xupsBatTimeRemaining # run time in seconds before UPS turns off
      - xupsBatVoltage # battery voltage
      - xupsBatteryAbmStatus # Advanced Baterry Management status
      - xupsBatteryAged # Indicates if the battery is over aged.
      - xupsBatteryFailure # Indicates if a battery fault detected or battery tests failed.
      - xupsBatteryLastReplacedDate # latest baterry replacement date
      #- xupsBatteryLowCapacity # Indicates if the battery capacity is below the threshold set in the UPS.
      - xupsBatteryNotPresent # Indicates if the UPS has no battery either internal or external.
      - xupsBypassVoltage # Bypass voltage
      #- xupsBypassAverageVoltage # AVG Bypass voltage
      #- xupsBypassCurrentHighPrecision # The measured bypass current from the UPS meters in tenth of amps.
      - xupsBypassFrequency # Bypass frequency in tenths of Hz
      # xupsBypassNumPhases # The number of lines in the UPS bypass table.
      - xupsBypassTotalCurrent # Bypass current from UPS in tenth of amps
      - xupsEnvAmbientTemp # Ambient temperature in the vicinity
      - xupsIdentManufacturer # Manufacturer name => EATON
      - xupsIdentModel # Model name
      #- xupsIdentOemCode # A binary code indicating who the UPS was manufactured or labeled for
      - xupsIdentPartNumber # P/N
      - xupsIdentSerialNumber # S/N
      - xupsIdentSoftwareVersion # SW version
      - xupsInputAverageVoltage # The measured input voltage from the UPS meters in volts
      - xupsInputFrequency # The utility line frequency in tenths of Hz.
      #- xupsInputId # value indicates what measurement is being stored in this table row : phase1 to neutral, phase2 to neutral, phase3 to neutral, phase1 to phase2, phase2 to phase3, phase3 to phase1.
      - xupsInputNumPhases # The number of input phases (normally 1 to 3).
      #- xupsInputSource_info # The present status of the primary AC input of the UPS # ERROR?
      - xupsInputVoltage # The measured input voltage from the UPS meters in volts.
      - xupsOutputCumulativePowerUsage # Energy consumed since last reset
      - xupsOutputCurrent # The measured UPS output current in amps.
      - xupsOutputCurrentHighPrecision # The measured UPS output frequency in tenths of Hz.
      - xupsOutputFrequency # The measured UPS output frequency in tenths of Hz.
      #-xupsOutputId # value indicates what measurement is being stored in this table row : phase1 to neutral, phase2 to neutral, phase3 to neutral, phase1 to phase2, phase2 to phase3, phase3 to phase1.
      - xupsOutputLoad # The UPS output load in percent of rated capacity.
      - xupsOutputNumPhases # The number of metered output phases.
      - xupsOutputPercentLoad # The percentage of the UPS power capacity presently being used on this output line.
      #- xupsOutputSource_info # The present source of output power.
      #- xupsOutputStatus_info # The present status of the AC output of the UPS. # ERROR?
      - xupsOutputTotalCurrent # The measured output current from the UPS meters in tenth of amps.
      #- xupsOutputTotalVA # The measured output apparent power in VA.
      - xupsOutputTotalWatts # The measured output active power in watts.
      - xupsOutputWatts # The measured real output power in watts.
      - xupsOutputVoltage # The measured output voltage from the UPS metering in volts.
    lookups:
      - source_indexes: [ xupsOutputPhase ]
        lookup: xupsOutputName
      - source_indexes: [ xupsInputPhase ]
        lookup: xupsInputName
      - source_indexes: [ xupsBypassPhase ]
        lookup: xupsBypassName
    overrides:
      xupsBatteryAbmStatus:
        type: EnumAsInfo
      xupsOutputStatus:
        type: EnumAsInfo
      xupsOutputSource:
        type: EnumAsInfo
      xupsInputStatus:
        type: EnumAsInfo
      xupsInputSource:
        type: EnumAsInfo
      xupsIdentSerialNumber:
        type: DisplayString
      xupsOutputName:
        type: DisplayString
      xupsInputName:
        type: DisplayString
      xupsBypassName:
        type: DisplayString
        ignore: true
      xupsIdentPartNumber:
        type: DisplayString
      xupsBypassPhase:
        ignore: true
      xupsBypassId:
        ignore: tru